Toyota Corolla: Garage door opener / Programming the Home- Link

■ Before programming Home- Link

■ Programming HomeLink

Steps 1 through 3 must be performed within 60 seconds, otherwise the indicator light will stop flashing and programming will not be able to be completed.

1 Press and release the Home- Link® button you want to program and check that the HomeLink® indicator light flashes (orange).

2 Point the remote control transmitter for the device at the rear view mirror, 1 to 3 in. (25 to 75 mm) from the HomeLink® buttons.

Keep the HomeLink® indicator light in view while programming.

Toyota Corolla. Programming the Home- Link

3 Program a device.

► Programming a device other than an entry gate (for U.S.A. owners)

Press and hold the handheld transmitter button until the HomeLink® indicator light changes from slowly flashing orange to rapidly flashing green (rolling code) or continuously lit green (fixed code), then release the button.

Toyota Corolla. Programming the Home- Link

Programming an entry gate (for U.S.A. owners)/Programming a device in the Canadian market

Press and release the remote control transmitter button at 2 second intervals, repeatedly,

until the HomeLink® indicator light changes from slowly flashing (orange) to rapidly flashing (green) (rolling code) or continuously lit (green) (fixed code).

4 Test the HomeLink® operation by pressing the newly programmed button and observing the indicator light:

5 Repeat the steps above to program another device for any of the remaining Home- Link® buttons.

■ Programming a rolling code system

2 or more people may be necessary to complete rolling code programming.

1 Locate the “Learn” or “Smart” button on the garage door opener motor in the garage.

This button can usually be found where the hanging antenna wire is attached to the unit. The name and color of the button may vary by manufacturer. Refer to the owner’s manual supplied with the garage door opener motor for details.

Toyota Corolla. Programming the Home- Link

2 Press and release the “Learn” or “Smart” button.

Perform 3 within 30 seconds after performing 2.

Toyota Corolla. Programming the Home- Link

3 Press and hold the desired

HomeLink® button (inside the vehicle) for 2 seconds and release it. Repeat this sequence

(press/hold/release) up to 3 times to complete programming.

If the garage door opener motor operates when the HomeLink® button is pressed, the garage door opener motor recognizes the HomeLink® signal.

Toyota Corolla. Programming the Home- Link

■ Enabling 2-way communication with a garage door (only available for compatible devices)

When enabled, 2-way communication allows you to check the status of the opening and closing of a garage door through indicators in your vehicle.

2-way communication is only available if the garage door opener motor used is a compatible device. (To check device compatibility, refer to www.homelink.com.)

1 Within 5 seconds after programming the garage door opener has been completed, if the garage door opener motor is trained to Home- Link®, both garage door operation indicators will flash rapidly (green) and the light on the garage door opener motor will blink twice, indicating that 2-way communication is enabled.

If the indicators do not flash, perperform 2 and 3 within the first 10 presses of the HomeLink® button after programming has been completed.

2 Press a programmed Home- Link® button to operate a garage door.

3 Within 1 minute of pressing the HomeLink® button, after the garage door operation has stopped, press the “Learn” or “Smart” button on the garage door opener motor. Within 5 seconds of the establishment of 2-way communication with the garage door opener, both garage door operation indicators in the vehicle will flash rapidly (green) and the light on the garage door opener motor will blink twice, indicating that 2-way communication is enabled.

■ Reprogramming a single HomeLink® button

When the following procedure is performed, buttons which already have devices registered to them can be overwritten:

1 With one hand, press and hold the desired HomeLink® button.

2 When the HomeLink® indicator starts flashing (orange), continue to hold the Home- Link® button and perform “Programming HomeLink®” 1 (it takes 20 seconds for the HomeLink® indicator to start flashing).

■ Before programming

System components
The HomeLink® wireless control system in your vehicle has 3 buttons which can be programmed to operate 3 different devices. Refer to the programming methods on the following pages to determine the ...

Operating HomeLink
Press the appropriate Home- Link® button. The HomeLink® indicator light should turn on. The status of the opening and closing of a garage door is shown by the indicators. A - Opening C - Closing ...

Other information:

Kia Niro 2017 (DE HEV) Service Manual: Crach Pad Center Panel Repair procedures
Replacement    Put on gloves to protect your hands.    • Use a plastic panel removal tool to remove interior trim pie ...

Toyota Corolla 2019-2022 Owners Manual: Initializing the tire pressure warning system
■ The tire pressure warning system must be initialized in the following circumstances: When rotating front and rear tires which have different tire inflation pressures. When changing the tire size. When the tire inflation pressure is changed such as when changing traveling speed or load weig ...

© 2016-2022 www.kniro.net