Kia Niro: Audio / Speakers Repair procedures

Kia Niro 2017 (DE HEV) Service Manual / Body Electrical System / Audio / Speakers Repair procedures

Inspection

Troubleshooting of the speakers

When handling the speakers :

•	Do not cause shock to the speakers by dropping or throwing them.

•	Be careful not to drop water and oil on the speakers.

•	Use caution to handle the speaker because diaphragm made of paper is easily torn by impact or external force.

•	Audio system tuning may cause damage to the speakers. The modified speakers are not covered by the manufacturer’s warranty.

1.	Basic inspection Loosen the screws to rule out the interference from the body trims and surrounding parts and then remove the speaker. After removing the speaker, check the sound quality of the speaker with the connector plugged in.

Inspection for each cause

(1)

Abnormal vibration

–	Make sure the mounting screws are properly tightened before replacing the speaker.

–	Reinstall the speaker and check that the symptom is resolved.

–	If the symptom does not disappear, replace the speaker with a new one.

(2)

Noise

–	Check that the speaker connector is properly connected and reinstall the connector if necessary.

–	If noises occur in the radio mode, turn to the CD player mode.

–	If noises occur in both modes, replace the speaker with a new one.

If noises occur only in the radio mode, the poor radio reception is the cause so do not replace the speaker.

(3)

Poor working

–	Check the plus (+) and negative (-) speaker terminals using an ohmmeter.

–	If resistance is measured at the specified value shown below, the speaker operation is normal.

–	If the measured resistance is different from the specified value, replace the speaker.

Removal

Front Door Speaker

1.	Disconnect the negative (-) battery terminal.

2.	Remove the front door trim. (Refer to Body - "Front Door Trim")

3.	Remove the front door speaker (B) after disconnecting the connector (A) and loosening the screws.

Tweeter Speaker

1.	Disconnect the negative (-) battery terminal.

2.	Remove the front pillar trim. (Refer to Body - "Front Pillar Trim")

Using a scraper or remover, remove the tweeter speaker grill (A).

Take care not to scratch the crash pad and related parts.

4.	Remove the tweeter speaker (A) after loosening the mounting screws.

5.	Disconnect the tweeter speaker connector (A).

Rear Door Speaker

1.	Disconnect the negative (-) battery terminal.

2.	Remove the rear door trim. (Refer to Body - "Rear Door Trim")

3.	Remove the rear door speaker (B) after disconnecting the connector (A) and loosening the screws.

Installation

Front Door Speaker

1.	Install the front door speaker.

2.	Install the front door trim.

3.	Connect the negative (-) battery terminal.

Tweeter Speaker

1.	Install the tweeter speaker.

2.	Install the tweeter speaker grill.

3.	Install the front pillar trim.

4.	Connect the negative (-) battery terminal.

Rear Door Speaker

1.	Install the rear door speaker.

2.	Install the rear door trim.

3.	Connect the negative (-) battery terminal.

•	Make sure that the speaker connectors are plugged in properly.

•	Check the audio system for normal operation.

Audio Unit Repair procedures

Removal • When removing with a flat-tip screwdriver or remover, wrap protective tape a ...

Antenna Components and components location

Components [AM/FM Antenna] ...

Other information:

Kia Niro 2017 (DE HEV) Service Manual: Power Relay Assembly (PRA) Specifications
Specification Power Relay Assembly (PRA) Item Specification Rated Voltage (V) 240 Rated Current (A) 80 ...

Kia Niro 2017 (DE HEV) Service Manual: Input Speed Sensor Description and operation
Description • The input shaft speed sensor is important in that it detects the input shaft RPM and sends this information to the Transmission Control Module (TCM). • This data is necessary for all operations including feedback control ...