Kia Niro: Keyless Entry And Burglar Alarm / Repair procedures

Kia Niro 2017 (DE HEV) Service Manual / Body Electrical System / Keyless Entry And Burglar Alarm / Repair procedures

Inspection

•	When removing with a flat-tip screwdriver or remover, wrap protective tape around the tools to prevent damage to components.

•	When removing the interior trim pieces, use a plastic panel removal tool not to damage the surface.

•	Be careful to store and handle the trim when removing/installing because lubricant and oil can leave a stain on the trim.

Front Door Lock Module Inspection

1.	Remove the front door trim. (Refer to Body - "Front Door Trim")

2.	Remove the front door module. (Refer to Body - "Front Door Module")

Disconnect the connector from the actuator.

[Central Lock Motor]

No.	Pin Information
No.	LH	RH
1	-	AJAR switch
2	Motor 1	COM
3	Motor 2	Lock / Unlock switch
4	Key unlock switch	Key lock switch
5	Key lock switch	Key unlock switch
6	Lock / Unlock switch	Motor 2
7	COM	Motor 1
8	AJAR switch	-

[Dead Lock Motor]

No.	Pin Information
No.	LH	RH
1	Motor 1	AJAR switch
2	Motor 2	COM
3	Motor 3	Lock / Unlock switch
4	Key unlock switch	Key lock switch
5	Key lock switch	Key unlock switch
6	Lock / Unlock switch	Motor 3
7	COM	Motor 2
8	AJAR switch	Motor 1

4.	Check actuator operation by connecting power and ground as shown below. To prevent damage to the actuator, apply battery voltage only momentarily. [Central Lock Motor] [Dead Lock Motor] [Central Lock Motor] (LH) (RH) [Dead Lock Motor]

Rear Door Lock Module Inspection

1.	Remove the rear door trim. (Refer to Body - "Rear Door Trim")

2.	Remove the rear door module. (Refer to Body - "Rear Door Module")

Disconnect the connector from the actuator.

[Central Lock Motor]

No.	Pin Information
No.	LH	RH
1	-	AJAR switch
2	Motor 1	COM
3	Motor 2	Lock / Unlock switch
4	-	-
5	-	-
6	Lock / Unlock switch	Motor 2
7	COM	Motor 1
8	AJAR switch	-

[Dead Lock Motor]

No.	Pin Information
No.	LH	RH
1	Motor 1	AJAR switch
2	Motor 2	COM
3	Motor 3	Lock / Unlock switch
4	-	-
5	-	-
6	Lock / Unlock switch	Motor 3
7	COM	Motor 2
8	AJAR switch	Motor 1

4.	Check actuator operation by connecting power and ground as shown below. To prevent damage to the actuator, apply battery voltage only momentarily. [Central Lock Motor] [Dead Lock Motor] [Central Lock Motor] (LH) (RH) [Dead Lock Motor]

Tailgate Lock Module Inspection

1.	Remove the tailgate trim. (Refer to Body - "Tailgate Trim")

2.	Disconnect the connectors from the actuator.

3.	Check actuator operation by connecting power and ground as shown below. To prevent damage to the actuator, apply battery voltage only momentarily.

4.	Checking the tailgate of the vehicle power option power refers to the tailgate module.

Tailgate Open Switch Inspection

1.	Disconnect the negative (-) battery terminals.

2.	Remove the tailgate trim (Refer to Body - "Tailgate Trim")

3.	Remove the tailgate latch. (Refer to Body - "Tailgate Latch")

4.	Disconnect the tailgate open switch assembly connector.

5.	Check for continuity between terminals in half latching condition as shown below.

Hood Switch Inspection

1.	Disconnect the hood switch connector (A).

2.	Check for continuity between the terminals and ground as shown below. (Refer to Body - "Hood Latch Assembly")

Burglar Horn Inspection

1.	Remove the burglar horn (A) after loosening the mounting bolt and disconnecting the connector (B).

2.	Test the burglar horn by connecting battery power to the terminal 2 and ground the terminal 1.

Description and operation

Description Burglar Alarm State [B/A State] B/A State Description DISARM 1) This is the state when "AR ...

Lane Departure Warning System (LDWS)

...

Other information:

Kia Niro 2017 (DE HEV) Service Manual: Stop Lamp Switch Components and components location
Components 1. Pedal stroke sensor 2. Stop lamp switch 3. Brake pedal arm ...

Kia Niro (DE HEV) Owners Manual: Air bag non-inflation conditions
In certain low-speed collisions the air bags may not deploy. The air bags are designed not to deploy in such cases because they may not provide benefits beyond the protection of the seat belts in such collisions. Air bags are not designed to inflate in rear collisions, because occupants ...