Kia Niro: Power Door Locks / Power Door Lock Module Repair procedures

Kia Niro 2017 (DE HEV) Service Manual / Body Electrical System / Power Door Locks / Power Door Lock Module Repair procedures

Inspection
  

When removing with a flat-tip screwdriver or remover, wrap protective tape around the tools to prevent damage to components.

When removing the interior trim pieces, use a plastic panel removal tool not to damage the surface.

Be careful to store and handle the trim when removing/installing because lubricant and oil can leave a stain on the trim.

Front Door Lock Module Inspection

1.

Remove the front door trim.

(Refer to Body - "Front Door Trim")

2.

Remove the front door module.

(Refer to Body - "Front Door Module")

3.

Disconnect the connector from the actuator.

[Central Lock Motor]

No.
Pin Information
LH
RH
1
-
AJAR switch
2
Motor 1
COM
3
Motor 2
Lock / Unlock switch
4
Key unlock switch
Key lock switch
5
Key lock switch
Key unlock switch
6
Lock / Unlock switch
Motor 2
7
COM
Motor 1
8
AJAR switch
-

[Dead Lock Motor]

No.
Pin Information
LH
RH
1
Motor 1
AJAR switch
2
Motor 2
COM
3
Motor 3
Lock / Unlock switch
4
Key unlock switch
Key lock switch
5
Key lock switch
Key unlock switch
6
Lock / Unlock switch
Motor 3
7
COM
Motor 2
8
AJAR switch
Motor 1

4.

Check actuator operation by connecting power and ground as shown below. To prevent damage to the actuator, apply battery voltage only momentarily.

[Central Lock Motor]

[Dead Lock Motor]

[Central Lock Motor]

(LH)

(RH)

[Dead Lock Motor]

Rear Door Lock Module Inspection

1.

Remove the rear door trim.

(Refer to Body - "Rear Door Trim")

2.

Remove the rear door module.

(Refer to Body - "Rear Door Module")

3.

Disconnect the connector from the actuator.

[Central Lock Motor]

No.
Pin Information
LH
RH
1
-
AJAR switch
2
Motor 1
COM
3
Motor 2
Lock / Unlock switch
4
-
-
5
-
-
6
Lock / Unlock switch
Motor 2
7
COM
Motor 1
8
AJAR switch
-

[Dead Lock Motor]

No.
Pin Information
LH
RH
1
Motor 1
AJAR switch
2
Motor 2
COM
3
Motor 3
Lock / Unlock switch
4
-
-
5
-
-
6
Lock / Unlock switch
Motor 3
7
COM
Motor 2
8
AJAR switch
Motor 1

4.

Check actuator operation by connecting power and ground as shown below. To prevent damage to the actuator, apply battery voltage only momentarily.

[Central Lock Motor]

[Dead Lock Motor]

[Central Lock Motor]

(LH)

(RH)

[Dead Lock Motor]

Tailgate Lock Module Inspection

1.

Remove the tailgate trim.

(Refer to Body - "Tailgate Trim")

2.

Disconnect the connectors from the actuator.

3.

Check actuator operation by connecting power and ground as shown below. To prevent damage to the actuator, apply battery voltage only momentarily.

4.

Checking the tailgate of the vehicle power option power refers to the tailgate module.

Power Door Lock Module Components and components location
Components 1. Door lock/unlock knob cable 2. Door inside handle cable 3. Door latch assembly ...

Power Door Lock Switch Repair procedures
Inspection [Non-IMS Type] 1. Check for continuity between the terminals. If there is an abnormality, replace the switch. ...

Other information:

Kia Niro 2017 (DE HEV) Service Manual: Photo Sensor Description and operation
Description The photo sensor is located at the center of the defrost nozzles. The photo sensor contains a photovoltaic (sensitive to sunlight) diode. The solar radiation received by its light receiving portion, generates an electromotive force in proportion to the amount of radia ...

Kia Niro 2017 (DE HEV) Service Manual: AVN Remote Controller Repair procedures
Removal 1. Disconnect the negative (-) battery terminal. 2. Remove the steering wheel assembly. (Refer to Steering System - "Steering Wheel") 3. Remove the steering back cover (A) after loosening the mounti ...

© 2016-2023 www.kniro.net