Kia Niro: Seat Electrical / Seat Heater Repair procedures

Kia Niro 2017 (DE HEV) Service Manual / Body Electrical System / Seat Electrical / Seat Heater Repair procedures

Inspection

Front Seat Heater

1.

Check for continuity and measure the resistance between terminals No 3 and No 6.

Standard value

Driver / Assists (cushion + back)

Heater seat : 1.77?±10%/23°C

Ventilated seat : 1.93?±10%/23°C

2.

Operate the seat heater after connecting the connector, and then check the thermostat by measuring the temperature of seat surface.

Standard value

1st : cushion : 36±2°C, back : 40±2°C

2st : cushion : 39±2°C, back : 45±2°C

3st : cushion : 42±2°C, back : 50±2°C

Rear Seat Heater

1.

Check for continuity and measure the resistance between terminals No 1 and No 4.

Standard value

Rear seat (Cushion only) : 3.16?±10%/23°C

2.

Operate the seat heater after connecting the connector, and then check the thermostat by measuring the temperature of seat surface.

Standard value

High (Cushion) : 38±2°C

Low (Cushion) : 42±2°C

Seat Heater Unit Diagnostic Mode

1.

Enter diagnostic mode by operating the seat heater switch.

2.

Enter diagnostic mode by referring to the below description.

•

Keep pressing the seat heater switch for over 3 seconds and release the switch. Then, within 2 seconds, press the switch again for over 3 seconds.

•

When diagnostic mode is entered, all switch LEDs will blink once.

3.

After entering diagnostic mode, check cause of failure according to blinking or illumination of LEDs.

[Driver Side / Passenger Side Seat Heater]

1st Row Seat Heater Unit

Failure Indication
Inspection Item
Cause of Failure
Low : OFF
Mid : OFF
High : FLASHING
Detect low voltage
–

IGN1 power below 8.5V

Detect over voltage
–

IGN1 power below 16.5V

Low : FLASHING
Mid : FLASHING
High : FLASHING
Broken fuse
–

B (+) fuse disconnected

Low : OFF
Mid : ON
High : FLASHING
Disconnected / Short NTC
–

NTC element defective

–

Short between NTC connector terminals

–

NTC (+) wiring disconnected

–

NTC (-) wiring disconnected

Low : FLASHING
Mid : FLASHING
High : FLASHING
Disconnected / Short heater
–

Heater element defective

–

Short between heater unit connector terminals

–

Heater (+) wiring disconnected

–

Heater (-) wiring disconnected

Low : ON
Mid : ON
High : FLASHING
Detect loss of temperature
–

If target temperature is not reached within 40 minutes


2nd Row Seat Heater Unit

Failure Indication
Inspection Item
Cause of Failure
Low : OFF
High : OFF
Detect low voltage
–

IGN1 power below 8.5V

Detect over voltage
–

IGN1 power below 16.5V

Low : FLASHING
High : FLASHING
Broken fuse
–

B (+) fuse disconnected

Low : OFF
High : FLASHING
Disconnection/Short in NTC
–

NTC element defective

–

Short between NTC connector terminals

–

NTC (+) wiring disconnected

–

NTC (-) wiring disconnected

Low : FLASHING
High : FLASHING
Disconnection/Short in heater
–

Heater element defective

–

Short between heater unit connector terminals

–

Heater (+) wiring disconnected

–

Heater (-) wiring disconnected

Low : ON
High : FLASHING
Detect loss of temperature
–

If target temperature is not reached within 40 minutes


4.

Check the defective area by the blinking pattern of LED lamps.

5.

Error is recorded by the seat heater unit.

6.

Error memory can be deleted by pressing the seat heater switch for over 5 seconds with the LED lamps blinking four times.

7.

Switching "OFF" the ignition will end the diagnostic mode for seat heater unit.

8.

Switch "ON" the ignition and check that seat heater system operates properly. To check the error code, refer to step 2 above.

Seat Heater Schematic diagrams
Circuit Diagram Front Seat Heater Rear Seat Heater ...

Seat Heater Switch Components and components location
Components Front Seat Switch 1. Driver side seat heater switch 2. Passenger side seat heater switch Rear Seat Switch ...

Other information:

Toyota Corolla 2019-2023 Owners Manual: If the vehicle is trapped in rising water
In the event the vehicle is submerged in water, remain calm and perform the following. Remove the seat belt first. If the door can be opened, open the door and exit the vehicle. If the door can not be opened, open the window using the power window switch and exit the vehicle through the window ...

Kia Niro 2017 (DE HEV) Service Manual: Pressure Source Unit Repair procedures
Removal 1. Turn ignition switch OFF and disconnect the negative (-) battery terminal. 2. Remove the air cleaner assembly. (Refer to Engine Mechanical System - "Air Cleaner") 3. Remove the brake fluid fro ...

© 2016-2023 www.kniro.net