Kia Niro: Hybrid Motor Cooling System / Radiator Repair procedures

Kia Niro 2017 (DE HEV) Service Manual / Hybrid Motor System / Hybrid Motor Cooling System / Radiator Repair procedures

Removal

1.	Disconnect the negative (-) cable of the 12V battery.

2.	Remove the under cover. (Refer to Engine Mechanical System - "Engine Room Under Cover")

3.	Drain the coolant of hybrid motor cooling system. (Refer to Hybrid Motor Cooling System - "Coolant")

4.	Remove the front bumper. (Refer to Body - "Front Bumper")

5.	Remove the active air flap. (Refer to Engine Mechanical System - "Active Air Flap")

6.	Remove the condenser. (Refer to Heating, Ventilation and Air Conditioning - "Condenser")

7.	Remove the upper air guard (A).

8.	Separate the radiator upper hose (A).

Loosen the nut (A).

Tightening torque :

8.8 - 13.7 N·m (0.9 - 1.4 kgf·m, 6.5 - 10.1 lb·ft)

10.	Separate the radiator lower hose (A).

11.

Remove the radiator (A) by loosening the nuts.

Tightening torque :

7.8 - 11.8 N·m (0.8 - 1.2 kgf·m, 5.8 - 8.7 lb·ft)

Installation

Install in the reverse order of removal.

•	Be careful not to damage other hoses nearby when tightening the clamp.

•	Install the clamp in the specified direction to prevent interference with surrounding components.

•	Refill the hybrid motor cooling system with coolant and then perform the air bleeding using the GDS/KDS. (Refer to Hybrid Motor Cooling System - "Coolant")

•	After installing, check for leakage of coolant or fluid from hose connection during engine start.

Inspection

Pressure Cap Testing

1.	Install the pressure cap and pressure tester on a SST (0K253-G5100).

2.	Apply a pressure of 79.4 - 122.58 kPa (0.95 - 1.25 kgf/cm², 11.5 - 17.78 psi).

3.	Check for a drop in pressure.

4.	If the pressure drops, replace the pressure cap.

Radiator motor Test

1.	Wait until motor is cool, then carefully remove the pressure cap and fill the reservoir tank with coolant, then install it on the pressure tester.

2.	Apply a pressure tester to the radiator and apply a pressure of 93.16 - 122.58 kPa (0.95 - 1.25 kgf/cm², 13.51 - 17.78 psi).

3.	Inspect for coolant leaks and a drop in pressure.

4.	Remove the tester and reinstall the pressure cap.

Radiator Components and components location

Components Location 1. Radiator 2. Drain plug 3. Radiator lower hose 4. Radiator upper hose ...

Electric Water Pump (EWP) Components and components location

Components Location 1. Eletric Water Pump (EWP) ...

Other information:

Kia Niro (DE HEV) Owners Manual: Headrest (for front seat)
The driver's and front passenger's seats are equipped with a headrest for the occupant's safety and comfort. The headrest not only provides comfort for the driver and front passenger, but also helps protect the head and neck in the event of a collision. WARNING For maximum ef ...

Kia Niro 2017 (DE HEV) Service Manual: Windshield Wiper-Washer Switch Repair procedures
Removal 1. Disconnect the negative (-) battery terminal. 2. Remove the steering wheel. (Refer to Steering System - "Steering Wheel") 3. Remove the steering column upper and lower shrouds after loosening the ...