Inspection |
[Non-IMS Type] |
Driver Power Window Switch
1. |
Disconnect the negative (-) battery terminal. |
2. |
Remove the driver front door trim. (Refer to Body - "Front Door Trim") |
3. |
Disconnect the power window switch connector from the door trim.
|
4. |
Check for continuity between the terminals in each switch position as shown below. [Power Window Switch Inspection]
[Power Door Lock Switch Inspection]
[Power Window Lock Switch Inspection]
|
Assist Power Window Switch
1. |
Disconnect the negative (-) battery terminal. |
2. |
Remove the assist front door trim. (Refer to Body - "Front Door Trim") |
3. |
Disconnect the power window switch connector from the door trim.
|
4. |
Check for continuity between the terminals in each switch position as shown below. [Power Window Switch Inspection]
[Power Door Lock Switch Inspection]
|
Rear Power Window Switch
1. |
Disconnect the negative (-) battery terminal. |
2. |
Remove the rear door trim. (Refer to Body - "Rear Door Trim") |
3. |
Disconnect the power window switch connector from the door trim.
[Power Window Switch Inspection]
[Rear Seat Heater Switch Inspection]
|
[IMS Type] |
Diagnosis With KDS/GDS
1. |
The body electrical system can be quickly diagnosed for failed parts by using vehicle diagnostic system (KDS/GDS). The diagnostic system (KDS/GDS) provides the following information.
|
2. |
Select the 'Car model' and the system to be checked in order to check the vehicle with the tester. |
3. |
Select the 'Body Control Module (BCM)' to check the driver seat or assist door module (DDM/ADM). |
4. |
Select the "Current Data" menu to check the current state of the input/output data. The input/output data for the sensors corresponding to the driver seat or assist door module (DDM/ADM) can be checked.
|
5. |
To check the power door lock operation by force, select "Actuation test". |
Removal |
Driver Power Window Switch
|
1. |
Disconnect the negative (-) battery terminal. |
2. |
Remove the driver front door trim. (Refer to Body - "Front Door Trim") |
3. |
Remove the power window switch assembly (A) after loosening the mounting screws.
|
Assist Power Window Switch
|
1. |
Disconnect the negative (-) battery terminal. |
2. |
Remove the assist front door trim. (Refer to Body - "Front Door Trim") |
3. |
Remove the power window switch assembly (A) after loosening the mounting screws.
|
Rear Power Window Switch
|
1. |
Disconnect the negative (-) battery terminal. |
2. |
Remove the rear door trim. (Refer to Body - "Rear Door Trim") |
3. |
Remove the power window switch assembly (A) after loosening the mounting screws.
|
Installation |
Driver Power Window Switch
1. |
Install the power window switch assembly. |
2. |
Install the driver front door trim after connecting the connector. |
3. |
Connect the negative (-) battery terminal. |
Assist Power Window Switch
1. |
Install the power window switch assembly. |
2. |
Install the assist front door trim after connecting the connector. |
3. |
Connect the negative (-) battery terminal. |
Rear Power Window Switch
1. |
Install the power window switch assembly. |
2. |
Install the rear door trim after connecting the connector. |
3. |
Connect the negative (-) battery terminal. |
Kia Niro (DE HEV) Owners Manual: To set cruise control speed
1. Press the CRUISE button, to turn the system on. The CRUISE indicator in the
instrument cluster will illuminate.
2. Accelerate to the desired speed. The smart cruise control speed can be set
as follows:
30 km/h (20mph) ~ 180 km/h (110 mph): when there is no vehicle in front
10 km/h (6 ...
Kia Niro (DE HEV) Owners Manual: Seat belt precautions
WARNING
All occupants of the vehicle must wear their seat belts at all times. Seat
belts and child restraints reduce the risk of serious or fatal injuries for all
occupants in the event of a collision or sudden stop. Without a seat belt, occupants
could be shifted too close to a deploying air ...