Inspection |
Inspect the following items by referring to inspection flow chart. (Refer to Inhibitor Switch - "Troubleshooting") |
1. |
Check the diagnostic trouble codes (DTC) using KDS/GDS. |
2. |
Inspect if "N" range setting matches. (Refer to Inhibitor Switch - "Installation") |
3. |
Check the free play for shift cable. (Refer to Shift Cable - "Installation") |
4. |
Check the condition of connector.
|
5. |
Inspect ground condition of rear combination lamp circuit. |
6. |
Inspect wiring connection condition of junction box power terminal and fuse lamp.
|
7. |
Check the inhibitor switch circuit signal.
Signal Code Table
|
Removal |
|
1. |
Place the shift lever in the "N" position. |
2. |
Shut off the high voltage circuit. (Refer to Automatic Transaxle System - "High Voltage Shut-off Procedure") |
3. |
Drain the coolant of hybrid cooling system. (Refer to Hybrid Motor System - "Coolant") |
4. |
Remove the hybrid power control unit (HPCU) assembly. (Refer to Hybrid Control System - "Hybrid Power Control Unit") |
5. |
Disconnect the TCM connector (A) and ECM connector (B).
|
6. |
Remove the TCM (A) and ECM (B).
|
7. |
Remove the HPCU tray (C) after removing the nut (A) and wiring mounting clips (B).
|
8. |
Loosen the shift cable mounting nut (A).
|
9. |
Remove the manual control lever (A).
|
10. |
Remove the inhibitor switch (A).
|
Installation |
1. |
Check that the shift lever is placed in the "N" position. |
2. |
Conntect the inhibitor switch connector (A).
|
3. |
Install the inhibitor switch (A).
|
4. |
Install the manual control lever (A).
|
5. |
Align the hole in the manual control lever with the "N" position hole of the inhibitor switch and then insert the SST inhibitor switch guide pin (0K948-E4000).
|
6. |
Tighten the manual lever mounting nut (A) to the specified torque.
|
7. |
Tighten the inhibitor switch mounting bolts (B) to the specified torque.
|
8. |
Tighten the nut (A) to the specified torque after removing free play by pushing the shift cable in the direction of the arrow.
|
9. |
Remove the SST (0K948-E4000) from the adjusment hole. |
10. |
Install the HPCU tray (A).
|
11. |
Install the wiring mounting clips (B) to HPCU tray and the tighten the nut (C).
|
12. |
Install the TCM (A) and ECM (B).
|
13. |
Connect the TCM connector (A) and ECM (B) connector.
|
14. |
Install the hybrid power control unit (HPCU) assembly. (Refer to Hybrid Control System - "Hybrid Power Control Unit" |
15. |
Refill the hybrid motor cooling system with coolant. (Refer to Hybrid Motor System - "Coolant") |
16. |
Connect the high voltage circuit. (Refer to Automatic Transaxle System - "High Voltage Shut-off Procedure") |
Kia Niro 2017 (DE HEV) Service Manual: Rear Wheel Guard Repair procedures
Replacement
Put on gloves to protect your hands.
•
Use a plastic panel removal tool to remove interior trim pie ...
Kia Niro 2017 (DE HEV) Service Manual: Specifications
Specifications
Items
Specifications
Model
RADIO/CD/MP3
Power supply
DC 14.4 V
Parasitic current
Max. 1mA (Head unit only)
Antenna
80PF 75?
...