Kia Niro: Hybrid Control System / Hybrid Power Control Unit (HPCU) Repair procedures

Kia Niro 2017 (DE HEV) Service Manual / Hybrid Control System / Hybrid Control System / Hybrid Power Control Unit (HPCU) Repair procedures

Removal

•	Be sure to read and follow the “General Safety Information and Caution” before doing any work related with the high voltage system. Failure to follow the safety instructions may result in serious electrical injuries.

•	Be sure to shut off the high voltage before doing any work related with the high voltage system(Refer to "High Voltage Shut-off Procedure"). Failure to follow the safety instructions may result in serious electrical injuries.

Hybrid Power Control Unit (HPCU)

1.	Shut off the high voltage circuit. (Refer to Hybrid Control System - “High Voltage Shutoff Procedure”)

2.	Remove the air cleaner assembly and air duct. (Refer to Engine Mechanical System - "Air Cleaner")

3.	Remove the ECM & TCM bracket assembly. (Refer to Engine Control/Fuel System - "Engine Control Module")

4.	Drain the coolant of hybrid motor cooling system. (Refer to Hybrid Motor Cooling System - "Coolant")

5.	Remove the HPCU protector (A) after loosening the mounting bolts.

6.	Disconnect the motor power cable connector (A) and HSG power cable connector (B).

Disconnect the power cable (A) [↔ High voltage battery system assembly] and power cable (B) [↔ HSG & Electric A/C compressor].

Remove the inverter power cable in the follwing order.

8.	Disconnect the HCU & inverter (MCU) connector (A).

9.	Disconnect the coolant outlet hose & pipe (A) after loosening the mounting bolt.

10.

Disconnect the LDC power output cable (A) and LDC ground (-) cable (C) after loosening the mounting bolt and nut.

LDC power (12V) output cable mounting nut :

10.8 - 13.7 N·m (1.1 - 1.4 kgf·m, 7.9 - 10.1 lb·ft)

LDC ground cable mounting bolt :

7.8 - 11.8 N·m (0.8 - 1.2 kgf·m, 5.8 - 8.7 lb·ft)

11.

Remove the HPCU (B) after loosening the mounting bolts.

HPCU mounting bolt :

21.6 - 23.5 N·m (2.2 - 2.4 kgf·m, 15.9 - 17.4 lb·ft)

12.	Remove the coolant hose & pipe (A) from the HPCU.

13.

Remove the reservoir (B) after loosening the mounting bolts.

Reservoir mounting bolt :

3.9 - 5.9 N·m (0.4 - 0.6 kgf·m, 2.9 - 4.3 lb·ft)

Hybrid Power Control Unit (HPCU) Tray

1.	Remove the hybrid power control unit. (Refer to Hybrid Control System - "Hybrid Power Control Unit (HPCU)")

Remove the hybrid power control unit tray (A) after loosening the mounting bolts.

Hybrid Power Control Unit (HPCU) tray mounting bolt :

21.6 - 23.5 N·m (2.2 - 2.4 kgf·m, 15.9 - 17.4 lb·ft)

Installation

•	Be sure to read and follow the “General Safety Information and Caution” before doing any work related with the high voltage system. Failure to follow the safety instructions may result in serious electrical injuries.

•	Be sure to shut off the high voltage before doing any work related with the high voltage system(Refer to "High Voltage Shut-off Procedure"). Failure to follow the safety instructions may result in serious electrical injuries.

1.	Install the HPCU in the reverse order of removal.

2.	Refill the hybrid motor cooling system coolant and perform air bleeding by using the KDS/GDS. (refer to Hybrid Motor Cooling System - "Coolant").

Adjustment

Perform HCU Variant Coding and Engine Clutch / Motor Resolver learning after replacing the HPCU.

HCU Variant Coding

1.	Switch "OFF" the ignition.

2.	Connect the KDS / GDS to Data Link Connector (DLC). Switch "ON" the ignition.

3.	Select "Vehicle, Model year, Engine, System".

4.	Select "Vehicle S/W Management".

5.	Select "HCU Variant Coding".

Engine Clutch / Motor Resolver learning procedure

Perform Engine Clutch / Motor Resolver learning after replacing the HPCU.

(Refer to Clutch System - "Engine Clutch Actuator")

Hybrid Power Control Unit (HPCU) Schematic diagrams

Hybrid Power Control Unit (HPCU) connector and high voltage cable Hybrid Power Control Unit (HPCU) terminal And Input/Output signal ECM Terminal Functi ...

Hybrid Control Unit (HCU) Schematic diagrams

HCU Terminal And Input/Output Signal Terminal Function Connector [C133-S] Pin No. Description Connected to 1 ...

Other information:

Kia Niro (DE HEV) Owners Manual: Emission control system
The emission control system of your vehicle is covered by a written limited warranty. Please see the warranty information contained in the Warranty & Maintenance book in your vehicle. Your vehicle is equipped with an emission control system to meet all applicable emission regulations. Th ...

Kia Niro 2017 (DE HEV) Service Manual: Rear Door Belt Outside Weatherstrip Repair procedures
Replacement 1. Pull down the rear door window glass to the lowest level by pressing the power window glass switch. 2. Remove the rear door belt outside weatherstrip (A) after loosening the mounting screw. 3. ...