Kia Niro: Front Suspension System / Front Stabilizer Bar Repair procedures

Kia Niro 2017 (DE HEV) Service Manual / Suspension System / Front Suspension System / Front Stabilizer Bar Repair procedures

Removal

1.	Disconnect the battery negative cable.

Remove the universal bolt (A).

Tightening torque :

32.4 - 37.3 N·m (3.3 - 3.8 kgf·m, 23.9 - 27.5 lb·ft)

•	Keep neutral range to prevent damaging the clock spring inner cable when steering the wheel.

•	Do not reuse the bolt.

Remove the wheel and tire.

Tightening torque:

107.9 - 127.5 N·m (11.0 - 13.0 kgf·m, 79.6 - 94.0 lb·ft)

Be careful not to damage the wheel nuts when removing the wheel and tire.

4.	Remove the under cover. (Refer to Engine Mechanical System - "Engine Room Under Cover")

Remove the tie rod end pin (A) and nub (B).

Tightening torque:

78.4 - 98.0 N·m (8.0 - 10.0 kgf·m, 57.8 - 72.3 lb·ft)

6.	Remove the knuckle by using the SST (09568-34000).

Remove the lower arm pin (A) and nut (B).

Tightening torque:

78.4 - 98.0 N·m (8.0 - 10.0 kgf·m, 57.8 - 72.3 lb·ft)

Remove the stabilizer link nut.

Tightening torque:

98.0 - 117.6 N·m (10.0 - 12.0 kgf·m, 72.3 - 86.7 lb·ft)

9.	Loosen the nuts and then remove the heat protector.

10.	Remove the hanger (A).

11.	Remove the roll rod bracket. (Refer to Engine Mechanical System - "Engine Mounting")

12.

Loosen the bolts (A) and (B) and then remove the coolant pipe.

Tightening torque:

6.8 - 10.7 N·m (0.7 - 1.1 kgf·m, 5.0 - 7.9 lb·ft)

13.

Loosen the bolts (A,B) and nuts (C,D) and then remove the sub frame (D).

Tightening torque:

Bolts :

(A) 44.1 - 53.9 N·m (4.5 - 5.5 kgf·m, 32.5 - 39.8 lb·ft)

(B) 156.9 - 176.5 N·m (16.0 - 18.0 kgf·m, 115.7 - 130.2 lb·ft)

Nuts :

(D) 44.1 - 53.9 N·m (4.5 - 5.5 kgf·m, 32.5 - 39.8 lb·ft)

Set up the transmission jack under the subframe in order to remove the shock absorber in no-load condition .

14.	Loosen the bolts and then remove the gearbox heat protector.

15.

Loosen the bolts and then remove the front stabilizer bar.

Tightening torque:

44.1 - 53.9 N·m (4.5 - 5.5 kgf·m, 32.5 - 39.8 lb·ft)

16.	Install in the reverse order of removal.

17.	Check the wheel alignment. (Refer to Suspension System - "Alignment")

Inspection

1.	Check the bushing for wear and deterioration.

2.	Check the front stabilizer bar for deformation.

3.	Check the front stabilizer link ball joint for damage.

Front Stabilizer Bar Components and components location

Components 1. Stabilizer bar 2. Stabilizer link ...

Sub Frame Repair procedures

Removal 1. Disconnect the battery negative cable. 2. Remove the universal bolt (A). Tightening torque : 32.4 - 37.3 N· ...

Other information:

Kia Niro 2017 (DE HEV) Service Manual: TPMS Receiver Repair procedures
Removal 1. Disconnect the battery negative cable. 2. Remove the glove box. (Refer to Body - "Glove Box Housing") 3. Disconnect the blower motor connector (A). 4. Disconnect ...

Kia Niro 2017 (DE HEV) Service Manual: Relay Box (Passenger Compartment) Repair procedures
Fuse Inspection 1. Check that the fuse holders are loosely held and that the fuses are securely fixed by the holders. 2. Check that each fuse circuit has the exact fuse capacity. 3. Check the fuses for any damage. ...