Kia Niro: Cylinder Head Assembly / CVVT & Camshaft Repair procedures

Kia Niro 2017 (DE HEV) Service Manual / Engine Mechanical System / Cylinder Head Assembly / CVVT & Camshaft Repair procedures

Removal

•	Use fender covers to avoid damaging painted surfaces.

•	To avoid damaging the cylinder head, wait until the engine coolant temperature drops below normal temperature (20°C [68°F]) before removing it.

•	When handling a metal gasket, take care not to fold the gasket or damage the contact surface of the gasket.

•	To avoid damage, unplug the wiring connectors carefully while holding the connector portion.

•	Turn the crankshaft pulley so that the No. 1 piston is at TDC (Top dead center).

Mark all wiring and hoses to avoid misconnection.

•	Be sure to read and follow the “General Safety Information and Caution” before doing any work related with the high voltage system. Failure to follow the safety instructions may result in serious electrical injuries.

•	Be sure to shut off the high voltage circuit according to the “High Voltage Shut-off Procedures” before doing any work related with the high voltage system to avoid serious electrical injuries.

1.	Shut off the High Voltage circuit. (Refer to General Information - "High Voltage Shutoff Procedure")

2.	Remove the cylinder head cover. (Refer to Cylinder Head Assembly - "Cylinder Head Cover")

Set No.1 cylinder to TDC (Top dead center) on compression stroke.

(1)	Turn the crankshaft pulley and align its groove with the timing mark of the timing chain cover.

(2)	Mark the timing chains corresponding to the timing marks of the CVVT sprockets.

4.	Remove the timing. (Refer to Timing System - "Timing Chain")

5.	Remove the intake CVVT assembly (A) and exhaust CVVT assembly (B).

Remove the camshaft.

(1)	Remove the camshaft front bearing cap and camshaft bearing cap in the sequence shown.

(2)	Remove the camshafts (A).

Inspection

Camshaft

Inspect the cam lobes.

Using a micrometer, measure the cam lobe height.

If the cam lobe height is less than specification, replace the camshaft.

Cam height :

Intake: 36..42 mm (1.4339 in.)

Exhaust: 36.15 mm (1.4232 in.)

2.	Check the surface of the camshaft journal for wear. If the journal is worn excessively, replace the camshaft.

Inspect the camshaft journal clearance.

(1)	Clean the bearing caps and camshaft journals.

(2)	Place the camshafts on the cylinder head.

(3)	Lay a strip of plastigage across each of the camshaft journal.

(4)

Install the camshaft front bearing cap and camshaft bearing cap in the sequence shown.

Tightening torque

Step 1

M6 bolts :

5.9 N.m (0.6 kgf.m, 4.3 lb-ft)

M8 bolts :

9.8 N.m (1.0 kgf.m, 7.2 lb-ft)

Step

2M6 bolts :

11.8 - 13.7 N.m (1.2 - 1.4 kgf.m, 8.7 - 10.1 lb-ft)

M8 bolts :

18.6 - 22.6 N.m (1.9 - 2.3 kgf.m, 13.7 - 16.6 lb-ft)

Do not turn the camshaft.

(5)	Remove the bearing caps.

(6)

Measure the plastigage at its widest point.

If the oil clearance is greater than specification, replace the camshaft. If necessary, replace the bearing caps and cylinder head as a set.

Camshaft bearing oil clearance

Intake

No. 1 :

0.032 - 0.062 mm (0.0013 - 0.0024 in.)

No. 2,3,4,5 :

0.027 - 0.057 mm (0.0011 - 0.0022 in.)

Exhaust

No. 1 :

0.027 - 0.057 mm (0.0011 - 0.0022 in.)

No. 2,3,4,5 :

0.027 - 0.057 mm (0.0011 - 0.0022 in.)

Inspect the camshaft end play.

(1)	Install the camshaft bearing caps.

(2)

Using a dial indicator, measure the end play while moving the camshaft back and forth.

If the end play is greater than specification, replace the camshaft.

If necessary, replace the bearing caps and cylinder head as a set.

Camshaft end play :

Standard :

0.10 - 0.20mm (0.0039 - 0.0079 in.)

(3)	Remove the camshafts.

Continuous variable valve timing (CVVT) Assembly

1.	Clamp the camshaft using a vise. Be careful not to damage the cam lobes and journals in the vise.

2.	Rotate the CVVT clockwise and counterclockwise to make sure that it is locked. It must not rotate.

3.	Intake CVVT : Seal one of the two advance holes in the camshaft journal with tape. Exhaust CVVT : Seal one of the two retard holes in the camshaft journal with tape.

Intake CVVT : Apply approx. 150 kPa (1.5 kgf/cm², 21 psi) of compressed air into the unsealed advance hole to release the lock.

Exhaust CVVT : Apply approx. 150 kPa (1.5 kgf/cm², 21 psi) of compressed air into the unsealed retard hole to release the lock.

Cover the oil paths with a piece of cloth when applying compressed air to prevent oil from spraying.

Intake CVVT : With compressed air applied, rotate the CVVT in the advance direction (counterclockwise) within its phasing range and check that the CVVT turns smoothly.

Exhaust CVVT : With compressed air applied, rotate the CVVT in the retard direction (clockwise) and check that the CVVT turns smoothly.

CVVT phasing range :

Intake : .35°±1°" (from the most retarded position to the most advanced position)

Exhaust : 20°±1°" (from the most advanced position to the most retarded position)

6.	Intake CVVT : Rotate the CVVT into the most retarded position (clockwise) and then check that the CVVT is locked. Exhaust CVVT : Rotate the CVVT into the most advanced position (counterclockwise) and then check that the CVVT is locked.

Installation

Install the camshaft.

(1)	Install the camshafts (A).

(2)

Install the camshaft front bearing cap and camshaft bearing cap in the sequence shown.

Tightening torque

Step

1M6 bolts :

5.9 N.m (0.6 kgf.m, 4.3 lb-ft)

M8 bolts :

9.8 N.m (1.0 kgf.m, 7.2 lb-ft)

Step

2M6 bolts :

11.8 - 13.7 N.m (1.2 - 1.4 kgf.m, 8.7 - 10.1 lb-ft)

M8 bolts :

18.6 - 22.6 N.m (1.9 - 2.3 kgf.m, 13.7 - 16.6 lb-ft)

Install the intake CVVT assembly (A) and exhaust CVVT assembly (B).

Tightening torque

Intake CVVT OCV bolt :

[47.1 - 52.0 N.m (4.8 - 5.3 kgf.m, 34.7 - 38.3 lb-ft)] + [25 - 31°]

Exhaust CVVT bolt :

63.7 - 73.5 N.m (6.5 - 7.5 kgf.m, 47.0 - 54.2 lb-ft)

Do not use any dropped intake OCV & center bolt.

3.	Install in the reverse order of removal.

CVVT & Camshaft Description and operation

Description Continuous Variable Valve Timing (CVVT) system advances or retards the valve timing of the intake and exhaust valve in accordance with the ECM control signal which is calc ...

Cylinder Head Repair procedures

Removal Engine removal is not required for this procedure. • Be sure to read and follow th ...

Other information:

Toyota Corolla 2019-2023 Owners Manual: When using a child restraint system
■ When installing a child restraint system to a front passenger seat For the safety of a child, install a child restraint system to a rear seat. When installing a child restraint system to a front passenger seat is unavoidable, adjust the seat as follows and install the child restraint system: ...

Kia Niro (DE HEV) Owners Manual: Easy access function
The system will move the driver's seat automatically as follows: Without smart key system - It will move the driver’s seat rearward when the ignition key is removed and front driver’s door is opened. - It will move the driver’s seat forward when the ignition key is inserted. W ...