Kia Niro: AHB(Active Hydraulic Boost) System / Brake Actuation Unit Repair procedures

Kia Niro 2017 (DE HEV) Service Manual / Brake System / AHB(Active Hydraulic Boost) System / Brake Actuation Unit Repair procedures

Removal

1.	Turn ignition switch OFF and disconnect the negative (-) battery terminal.

2.	Disconnect the TCM connector. (Refer to DCT (Dual Clutch Transmission) System - "DCT Control Module (TCM))

3.	Disconnect the ECM connector.

4.	Remove the air cleaner assembly. (Refer to Engine Mechanical System - "Air Cleaner")

Remove the brake fluid from the reservoir .

Do not spill brake fluid on the vehicle, it may damage the paint; if brake fluid does contact the paint, wash it off immediately with water.

Remove the nuts, hose, brake fluid level sensor connector (A).

Tightening torque:

6.8 - 10.7 N·m (0.7 - 1.1 kgf·m, 5.0 - 7.9 lb·ft)

Disconnect the integrated brake actuation unit (IBAU) connector and brake tube.

The following section describes how to diagnose faults using a diagnostic instrument.

1)	Connect the diagnostic instrument to the self-diagnostic connector (16-pin) beneath the crash pad on the side of driver's seat, and then turn on the ignition to activate the diagnostic instrument

2)	In the GDS Vehicle Type Selection menu, select "Vehicle Type" and "Brake/VDC/AHB" System.

3)	Disconnect the negative (-) battery terminal.

Loosen the flare nuts (A) from the integrated brake actuation unit (IBAU) and then remove the brake tube.

Tightening torque:

12.7 - 16.7 N·m (1.3 - 1.7 kgf·m, 9.4 - 12.3 lb·ft)

9.	Remove the snap pin (A) and clebis pin (B).

10.

Loosen the brake pedal nuts.

Tightening torque :

16.7 - 25.5 N·m (1.7 - 2.6 kgf·m, 12.3 - 18.8 lb·ft)

Installation

1.	Installation is the reverse of removal.

2.	Check the brake pedal operation.

3.	After filling the brake fluid in the reservoir, perform the air bleed. (Refer to the Brake system - "Brake Bleeding Procedure")

4.	Conduct the variant coding.

5.	Conduct the pedal traval sensor (PTS) calibration.

6.	Conduct the longitidinal G sensor clibration. (HAC/DBC Only)

7.	Conduct the pressure sensor calibration.

8.	Conduct the auto detected configuration reset the if necessary.

Diagnosis by using diagnostic device

The following section describes how to diagnose faults using a diagnostic instrument.

1.	Connect the diagnostic instrument to the self-diagnostic connector (16-pin) beneath the crash pad on the side of driver's seat, and then turn on the ignition to activate the diagnostic instrument.

2.	In the GDS vehicle type selection menu, select "Vehicle Type" and "Brake/VDC/AHB" System. Longitudinal G Sensor Calibration(HAC/DBC Only) Pressure Sensor Calibration Pedal Travel Sensor (PTS) Calibration Auto Detected Configuration Reset(ESP(ESC) Only) VARIANT CODIN

Brake Actuation Unit Components and components location

Components 1. Integrated Brake Actuation Unit (IBAU) ECU 2. Reservoir 3. Pedal Simulator 4. Integrated Brake Actuation Unit (IBAU) ...

Pressure Source Unit Components and components location

Components 1. Pressure Source Unit (PSU) 2. Motor 3. Filler adapter 4. Accumulator 5. Bracket ...

Other information:

Kia Niro (DE HEV) Owners Manual: Tail lamp (inside) bulb replacement
1. Open the tailgate. 2. Remove the service cover. 3. Remove the socket from the assembly by turning the socket counterclockwise until the tabs on the socket align with the slots on the assembly. 4. Remove the bulb from the socket by pressing it in and rotating it counter-clockwise until ...

Kia Niro (DE HEV) Owners Manual: How does the air bag system operate
Air bags are activated (able to inflate if necessary) only when the ignition switch is turned to the ON or START position. Air bags inflate instantly in the event of a serious frontal collision or side collision (if equipped with a side air bag or curtain air bag) in order to help prot ...