Inspection |
Front Washer Motor
1. |
With the washer motor connected to the reservoir tank, fill the reservoir tank with water.
|
2. |
Connect positive (+) battery cables to terminal 1 and negative (-) battery cables to terminal 2 respectively. |
3. |
Check that the motor operates normally and the washer motor runs and water sprays from the front nozzles. |
4. |
If they are abnormal, replace the washer motor. [Front & Rear washer]
|
Washer Fluid Level Sensor Switch
1. |
Disconnect the negative (-) battery terminal. |
2. |
Drain the washer fluid less than 650 cc. |
3. |
Check for continuity between the No. 1 and No.2 terminal in each float position. There should be continuity when the float is down. There should be no continuity when the float is up. |
4. |
If the continuity is not as specified, replace the washer fluid level switch
|
5. |
If the continuity is not as specified, replace the washer fluid level switch. |
Removal |
Front Washer Motor
1. |
Disconnect the negative (-) battery terminal. |
2. |
Remove the engine room under cover. (Refer to Engine Mechanical System - "Engine Room Under Cover") |
3. |
Remove the front wheel guard [RH]. (Refer to Body - "Front Wheel Guard") |
4. |
Drain the washer fluid to less than 650 cc. |
5. |
Disconnect the washer hose (A) and washer motor connector (B). |
6. |
Remove the front washer motor (C).
|
Washer Fluid Level Sensor Switch
1. |
Disconnect the negative (-) battery terminal. |
2. |
Remove the engine room under cover. (Refer to Engine Mechanical System - "Engine Room Under Cover") |
3. |
Remove the front wheel guard [RH]. (Refer to Body - "Front Wheel Guard") |
4. |
Drain the washer fluid to less than 650 cc. |
5. |
Remove the washer fluid level sensor switch (B) after disconnecting the connector (A).
|
Reservoir Tank
1. |
Disconnect the negative (-) battery terminal. |
2. |
Remove the engine room under cover. (Refer to Engine Mechanical System - "Engine Room Under Cover") |
3. |
Remove the front wheel guard [RH]. (Refer to Body - "Front Wheel Guard") |
4. |
Drain the washer fluid to less than 650 cc. |
5. |
Disconnect the washer hoses (A) and connector (B). |
6. |
Remove the reservoir tank (C) after loosening the bolts.
|
Installation |
Front Washer Motor
1. |
If necessary, clean the washer motor filter.
|
2. |
Install the front washer motor. |
3. |
Connect the front washer motor connector. |
4. |
Install the front wheel guard [RH]. |
5. |
Install the engine room under cover. |
6. |
Connect the negative (-) battery terminal. |
Washer Fluid Level Sensor Switch
1. |
If necessary, clean the washer motor filter.
|
2. |
Install the washer fluid level sensor switch. |
3. |
Connect the washer fluid level sensor switch connector. |
4. |
Install the front wheel guard [RH]. |
5. |
Install the engine room under cover. |
6. |
Connect the negative (-) battery terminal. |
Reservoir Tank
1. |
If necessary, clean the washer motor filter.
|
2. |
Install the reservoir tank. |
3. |
Install the washer motor hose and connectors. |
4. |
Install the front wheel guard [RH]. |
5. |
Install the engine room under cover. |
6. |
Connect the negative (-) battery terminal. |
Kia Niro (DE HEV) Owners Manual: Important - use of compact spare tire
Your vehicle is equipped with a compact spare tire. This compact spare tire takes
up less space than a regular- size tire. This tire is smaller than a conventional
tire and is designed for temporary use only.
CAUTION
You should drive carefully when the compact spare is in use. The compact
...
Peugeot 2008 2019-2023 Owner's Manual: Changing a wiper blade
Removing/refitting at the front
Carry out these wiper blade replacement operations from the driver's
side.
Starting with the wiper blade farthest from you, hold each arm by the
rigid section and raise it as far as possible.
Do not touch the wiper
blades - risk of irreversible distortion.
...