Specification |
Engine |
Joint type |
Max. permissible angle |
||
Outer |
Inner |
Outer |
Inner |
|
1.6 GDI KAPPA |
BJ#24 |
VTJ#24 |
46.5° |
23° |
Tightening Torques
Items |
N·m |
kgf·m |
lb·ft |
|
Front |
Wheel nut |
107.9 - 127.5 |
11.0 - 13.0 |
79.6 - 94.0 |
Driveshaft caulking nut |
274.6 - 294.2 |
28.0 - 30.0 |
202.5 - 217.0 |
|
Strut assembly lower mounting bolt |
156.9 - 176.5 |
16.0 - 18.0 |
115.7 - 130.2 |
|
Wheel speed sensor mounting bolt |
8.8 - 13.7 |
0.9 - 1.4 |
6.5 - 10.1 |
|
Brake disc mounting screw |
4.9 - 5.8 |
0.5 - 0.6 |
3.6 - 4.3 |
|
Hub assembly mouning bolt |
88.3 - 107.9 |
9.0 - 11.0 |
65.1 - 79.6 |
|
Inner shaft bearing brakcet bolt |
49.0 - 63.7 |
5.0 - 6.5 |
36.2 - 47.0 |
|
Lower arm ball joint mounting bolt |
98.0 - 117.6 |
10.0 - 12.0 |
72.3 - 86.7 |
|
Tie rod end ball joint nut |
78.4 - 98.0 |
8.0 - 10.0 |
57.8 - 72.3 |
|
Stabilizer link |
98.0 - 117.6 |
10.0 - 12.0 |
72.3 - 86.7 |
|
Rear |
Wheel nut |
107.9 - 127.5 |
11.0 - 13.0 |
79.6 - 94.0 |
Brake caliper mounting bolt |
78.4 - 98.0 |
8.0 - 10.0 |
57.8 - 72.3 |
|
Brake disc mounting screw |
4.9 - 5.8 |
0.5 - 0.6 |
3.6 - 4.3 |
|
Hub assembly mouning bolt |
88.3 - 107.9 |
9.0 - 11.0 |
65.1 - 79.6 |
|
Upper arm mounting bolt |
137.2 - 156.9 |
14.0 - 16.0 |
101.2 - 115.7 |
|
Lower arm mounting bolt |
137.2 - 156.9 |
14.0 - 16.0 |
101.2 - 115.7 |
|
Asist arm mounting bolt |
137.2 - 156.9 |
14.0 - 16.0 |
101.2 - 115.7 |
|
Trailing arm mounting bolt |
137.2 - 156.9 |
14.0 - 16.0 |
101.2 - 115.7 |
Lubricants |
Item |
Lubricants |
Quantity |
|
1.6 GDI KAPPA |
BJ(LH) |
RBA |
100 ~ 110g |
VTJ(LH) |
CW-13TJ |
145 ~ 155g |
|
BJ(RH) |
RBA |
100 ~ 110g |
|
VTJ(RH) |
CW-13TJ |
145 ~ 155g |
Kia Niro 2017 (DE HEV) Service Manual: Front Door Belt Inside Weatherstrip Repair procedures
Replacement
1.
Remove the front door trim.
(Refer to Front Door - "Front Door Trim")
2.
Remove the front door belt inside weatherstrip (A).
3.
Install in the reverse order of removal.
...
Kia Niro 2017 (DE HEV) Service Manual: Repair procedures
Inspection
AEB function ON / OFF switch was included to USM (User Setting Menu) and the
state of the factory is ON.
When the IGN On, maintain ON condition by default. And does not reflect the driver
settings when next IGN On.
If turned the ESP function Off, the AEB function is t ...