Toyota Corolla: Dynamic radar cruise control with full-speed range / Selecting constant speed control mode

When constant speed control mode is selected, your vehicle will maintain a set speed without controlling the vehicle-to-vehicle distance. Select this mode only when vehicle-to-vehicle distance control mode does not function correctly due to a dirty radar, etc.

1 With the cruise control off, press and hold the cruise control main switch for 1.5 seconds or more.

Immediately after the switch is pressed, the dynamic radar cruise control indicator will come on. Afterwards, it switches to the cruise control indicator.

Switching to constant speed control mode is only possible when operating the switch with the cruise control off.

Toyota Corolla. Selecting constant speed control mode

2 Accelerate or decelerate, with accelerator pedal operation, to the desired vehicle speed (at or above approximately 20 mph [30 km/h]) and press the “-SET” switch to set the speed.

Cruise control “SET” indicator will come on.

The vehicle speed at the moment the switch is released becomes the set speed.

Toyota Corolla. Selecting constant speed control mode

■Dynamic radar cruise control with full-speed range can be set when

■Accelerating after setting the vehicle speed

The vehicle can accelerate by operating the accelerator pedal. After accelerating, the set speed resumes. However, during vehicle- to-vehicle distance control mode, the vehicle speed may decrease below the set speed in order to maintain the distance to the preceding vehicle.

■When the vehicle stops while follow-up cruising

●Pressing the “+RES” switch while the vehicle ahead stops will resume follow-up cruising if the vehicle ahead starts off within approximately 3 seconds after the switch is pressed. ●If the vehicle ahead starts off within 3 seconds after your vehicle stops, follow-up cruising will be resumed.

■Automatic cancelation of vehicle- to-vehicle distance control mode

Vehicle-to-vehicle distance control mode is automatically canceled in the following situations.

If vehicle-to-vehicle distance control mode is automatically canceled for any reasons other than the above, there may be a malfunction in the system. Contact your Toyota dealer.

■Brake operation

A brake operation sound may be heard and the brake pedal response may change, but these are not malfunctions.

■Warning messages and buzzers for dynamic radar cruise control with full-speed range

Warning messages and buzzers are used to indicate a system malfunction or to inform the driver of the need for caution while driving. If a warning message is shown on the multi-information display, read the message and follow the instructions.

■When the sensor may not be correctly detecting the vehicle ahead

In the case of the following and depending on the conditions, operate the brake pedal when deceleration of the system is insufficient or operate the accelerator pedal when acceleration is required. As the sensor may not be able to correctly detect these types of vehicles, the approach warning (®P.236) may not be activated.

Toyota Corolla. Selecting constant speed control mode

Toyota Corolla. Selecting constant speed control mode

Toyota Corolla. Selecting constant speed control mode

■Conditions under which the vehicle-to-vehicle distance control mode may not function correctly

In the case of the following conditions, operate the brake pedal (or accelerator pedal, depending on the situation) as necessary.

As the sensor may not be able to correctly detect vehicles ahead, the system may not operate properly.

Toyota Corolla. Selecting constant speed control mode

Toyota Corolla. Selecting constant speed control mode

Approach warning (vehicle- to-vehicle distance control mode)
When your vehicle is too close to a vehicle ahead, and sufficient automatic deceleration via the cruise control is not possible, the display will flash and the buzzer will sound to alert the driver. ...

Dynamic radar cruise control
In vehicle-to-vehicle distance control mode, the vehicle automatically accelerates and decelerates to match the speed changes of the preceding vehicle even if the accelerator pedal is not depressed. ...

Other information:

Kia Niro 2017 (DE HEV) Service Manual: Instrument Cluster Description and operation
Description Communication Network Diagram Abbreviation Expalnation AAF Active Air Flap ACU Airbag Control Unit AEB Autonomous Emergency Braking AHB ...

Kia Niro 2017 (DE HEV) Service Manual: Description and operation
Description 1. To display back of the vehicle to assist the driver, it receives vehicle rearside image signal from the rearview camera and displays it on AVN head unit monitor or LHS of inside rearview mirror. 2. Back view camera is a sup ...

© 2016-2022 www.kniro.net